DEFENS PE-02 (2K) Water-based epoxy primer

The primer is used as a base mixture for concrete when installing thin-layer, monolithic, high-filled polyurethane, polyamide, and epoxy coatings in industrial, commercial, residential, and public buildings and structures, at transport infrastructure facilities, warehouses, terminals, parking lots, when installing insulation cladding for collectors, tanks, artificial reservoirs, etc.

It is designed for pre-priming surfaces before applying the finishing polymer coating. It is used for sealing and strengthening porous and weak substrates, preventing dust formation, ensuring reliable adhesion of the finishing polymer coating, especially on glossy or polished surfaces.

It is applied for priming concrete, screeds, plasters, colored and black metals, slate, tiles, bricks, artificial and natural stone, bitumen-based materials, drywall, fiberboard, particleboard, plywood, and wood. It is used for priming the screed before laying floor coverings (parquet, laminate, linoleum, etc.) and roll waterproofing (PVC, EPDM, TPO, etc.).

Advantages and features of the material:

Easy to use water-soluble non-toxic material;
No harmful impact on the environment;
Increased abrasion resistance;
Exceptionally high adhesion and penetrating ability to all substrates;
Possible application on damp and wet substrates;
Withstands negative hydrostatic pressure.
With the additional introduction of quartz sand or other mineral fillers, it is used to prepare putty, leveling, and repair polymer concrete mixtures.
Convenient to work with and safe material for professional use.

Recommendations for use:

Requirements for the properties and preparation of the concrete substrate:

The properties of the concrete substrate and methods for preparing its surface must comply with current building and technical regulations. The substrate must be strong, homogeneous, clean, dry, free from oils, fats, brittle areas, remnants of old peeling coatings, and other contaminants that hinder adhesion. The main requirements for the concrete substrate: compressive strength – at least 20 N/mm2, tensile strength – at least 1.5 N/mm2. Treat the concrete substrate using abrasive tools, shot blasting, milling, or grinding equipment. For concrete floors with a strengthened top layer, only shot blasting treatment is allowed. Carefully remove dust generated during processing using an industrial vacuum cleaner.

Requirements for application conditions:

The temperature of the primer components, the surface of the substrate, and the surrounding air in the work area: from +10°C to +25°C.

Attention! The temperature of the substrate surface must be at least 3°C above the measured dew point both during the application of the primer and throughout the time required for complete polymerization/drying of the primer layer. Relative humidity of the air: no more than 70%.

Method of application:

Pour the entire volume of components 1 and 2 into a mixing container of appropriate volume and mix thoroughly until homogeneous for 2-3 minutes. Use a low-speed (300-400 rpm) electric mixer for mixing the components.

DO NOT MIX COMPONENTS BY HAND!

Attention! Depending on the reactivity of the components, the curing process of the epoxy composition is accompanied by the release of a certain amount of heat. The “self-heating” of the mixture of epoxy composition components in the mixing container may provoke its premature curing. Therefore, it is strongly recommended not to leave the primer.Prepared mixture of epoxy composition components directly in the mixing container for an extended period.

Application methods: brush, roller.

Packaging and storage

The primer is supplied in airtight plastic containers. The set consists of two components (A, B), with a total weight of 10 kg; 20 kg. Store the primer in a tightly closed container, protecting it from moisture and direct sunlight, away from heat sources, at a temperature of +5 to +30°C. Do not freeze! The shelf life is 6 months from the date of manufacture without violating storage conditions.

Cleaning tools

Working tools and equipment should be rinsed with water immediately after use. Cured mixture can only be removed mechanically.

Safety measures

Persons working with epoxy primer must be provided with personal protective equipment. All work should be carried out in rooms equipped with supply and exhaust ventilation. In case of contact with skin or eyes, rinse thoroughly with water and seek medical attention if necessary. After complete drying and polymerization, the primer (putty) layer is completely safe and permitted for use in seamless polymer coating systems in public, residential, and industrial premises, including food production, catering establishments, pharmaceutical industry, agriculture, and in children’s and medical institutions.

When carrying out work, use personal protective equipment, avoid contact with eyes, respiratory tract, and skin. Keep away from fire.